![Click to enlarge]()
|
Handgun targets with center holes are attached to target holders
with a modified plow bolt, lock washer and cinch nut. We also
provide a hard thick washer to be placed between the target and
mounting bracket. The spacer washer helps to maintain the ring by
minimizing the contact between the plate and bracket.
(Click on the picture to enlarge it)
|
|
Handgun targets with center holes can be used with our A-frame and
pendulum combination. The pendulum adapter, has a hole allocated for
center hole targets, and is furnished with a modified plow bolt, lock washer and nut. We also
provide a hard thick washer to be placed between the target and
pendulum bracket. The spacer washer helps to maintain the ring by
minimizing the contact between the plate and bracket.
(Click on the picture to enlarge it)
|
|
The stem mount adapter is our newest offering. It offers noise and movement when hit.
The very center of the target isn't as alive to impacts as is the
remainder of the target, but usually, there is still movement. It's other main advantage is it's ease of
mounting - just set it over the stem - it's done!. Removal of the plate
and adapter is recommended before pulling the stem from it's holder or
moving the entire target and base (doing so will save wear and tear on
your feet). The mounting assembly attaches to the plate with a 1/2"
modified plow share bolt, lock washer and nut. A thick, hard washer
provides minimal contact between the plate and mounting bracket to
maximize ringing.
The mounting hardware is available as the "Center Hole -
Bolt, Washers, Nut" kit.
(Click on the picture to enlarge it)
|
|
The Disconnector consists of a Stem Platform and plate Reactive Base.
The Stem Platform will fit on any 1 1/2" x 1 1/2" x 1/4 angle
iron. It goes onto the end of a stem like the stem mount adapter. The
platform can be used with any knock off style target. The platform top
surface is 4" x 6".
The plate Reactive Base has an anti-spin strip welded to the rear of the
bottom side of its platform. The strip insures that the Reactive Base is
properly aligned when resetting it onto the Stem Platform. One of our Center Hole
target can be fastened to the Reactive Base with a modified Plow bolt, Lock
washer and nut. Targets up to 6" from the edge to the center hole
can be used.
(Click on the picture to enlarge it)
|
|
Our small popper base will accept either the AR400
IPSC Mini Classic or Mini Pepper (2/3 size) Popper targets.
We offer a forward falling kit that replaces the adjustment
bolt.
We also have an actuator lever that can be bolted to the plate hinge to
permit tripping of other devices/targets. A forward fall kit is
required when the lever is used.
We protect the hinge and adjusting bolt with a V shaped deflector. The
deflector will divert a full house .44 Magnum projectile.
The base is usable without installing the legs. We provide the legs in
case the terrain won't let the base be stable.
We build our own hinges to reduce the slop commonly found in other
bases. Reset and trip points will remain constant. The base material
weight and leg sockets help prevent plate/base scooting.
We strongly urge that the pad that accepts the falling plate be kept
free of debris. Stones or other hard substances will cut or compress the
pad material when the target is driven down.
(Click on the picture to enlarge it)
|
|
Picture Pending
|
Our large popper base will
accept AR400 full size Pepper Popper or the Classic Popper IPSC targets.
The large popper base also uses the same forward falling kit as
is used for the small base.
Its hinge is also protected by a V shaped deflector.
The base is usable without installing the legs. We provide the legs in
case the terrain won't let the base be stable.
Again - we strongly urge that the pad that accepts the falling plate be kept
free of debris.
(Click on the picture to enlarge it)
|
|
The Forward falling Converter Kit converts the
rearward falling AR400 base into a forward falling one. The set bolt is
removed and our Kit assembly is installed in its place. The popper
assembly then is rotated 180 degrees. Plate sensitivity can still be
adjusted. When the plate is hit it will fall toward the shooter.
(Click on the picture to enlarge it)
|
|
The Actuator Lever is bolted to the upper hinge assembly. The kit
has an attachment point for a cable or rope. It is used to trip or
activate other targets. The Forward falling kit is required to
effectively use the lever.
(Click on the picture to enlarge it)
|
|
Mounting the plates to the plate rack only requires two bolts, and
associated lock washers and nuts. Each kit will mount one target to one
of six plate rack hinges positions.
(Click on the picture to enlarge it)
|
|
The Reactive Base kits can use any of the targets of the plate rack
series. The same plate rack hardware kit is furnished with the Reactive Base. The
base has a piece of angle iron welded on the rear which prevents the
target from spinning.
Need Reactive base picture
|
